How to install chain link fence for your yard

How to Install a Chain Link Fence

If you’re looking to put a fence around your home or property, this fence idea may just be the thing for you.

 Get ready to add this to your homesteading skills.

Remember: Before you start digging, be sure to check for any underground utilities.

Fencing Materials You’ll Need:

  • measuring tape
  • posthole digger
  • wheelbarrow
  • shovel
  • hoe
  • carpenter’s level
  • 1/2″ and 9/16″ wrench
  • hacksaw
  • fence stretcher
  • pliers
  • tension wire clip
  • chalk line
  • stakes
  • fence fabric
  • posts
  • gravel
  • concrete
  • batter board
  • mason string

How to Install a Chain Link Fence From Start To Finish

Thank you LOWE’s Youtube for the awesome tutorial! You can watch the full tutorial at the bottom of this post.

Step 1

Measure the area you’re going to build your fence in using your measuring tape.

 Mark the corners using a batter board and mason string.

Step 2

Start making a lay out of where the posts will go. The spacing is normally indicated by

the manufacturer but it should never exceed 10 feet on center. Once you’ve done the measurements, 

start marking the spots with a wooden stake.    

Step 3

Now that you’ve marked and spaced out where the posts should go, you can start digging.

Step 4

Start prepping your posts. Mark where the ground level should be to make sure 

they’re set at the correct height. Normally it should be the height of your chain link minus

two inches and height of the chain link plus two inches for the end or terminal posts.

Step 5

Time to set your posts in the hole. Start with a terminal post by adding some 

gravel first to ensure that the mark you made earlier is level with the ground. 

Use some braces and clamps to hold it in place then add the concrete and water. 

Once that’s done, work it out a bit so it will be two inches below ground level. 

Repeat this process with all your other posts.

Step 6

Now that the concrete has hardened, you can start attaching the fence hardware. 

Add the tension bands and bolts. Make sure that the flat side of the band is in the fabric 

side of the fence. For the corner post, you’ll need to add another tension band for 

the adjacent side of the fence.

TIP: Want to know how many tension bands you need? Measure the height of your post in feet minus one.

Step 7

Add your top rail bands and cups by screwing them in place. When working with the 

corner post, be sure that the offset cups alternate.

Step 8

  Add the post cap to the terminal post.

  Add the caps on the line post with the rings facing the fence side.

Add the post cap for the corner post and for the line posts, add the cap with 

the ring offset towards the fabric side of the fence.

Step 9

You can now slide the top rail to the line post top and into the rail end 

cup then tighten the bolts.

Step 10

Keep adding top rails along; sliding them inside the rings on your line posts. 

When you reach the other end of the terminal post, cut the top post so it can fit 

the rail end cup.

TIP: To add extra support you can also add an additional tension wire at the 

bottom of the posts.

Step 11

Now that you have the posts all set, next thing to do is attach the fabric. 

Take the end of the chain link and insert a tension bar in the end of the fabric 

and the tension bands on the terminal post.

Step 12

Unroll the fabric out on the ground and stand it up against the fence. 

Try to stretch it out as best as you can.

As you lay it out, attach some wire ties to hold the fabric in place.

Step 13

Once you’ve reached the end, it’s time to tighten the fabric. Remove the any 

excess first by opening the loop at the top and bottom. After that, just twist the strand out.

Step 14

To tighten the chain link, insert a tension bar about 3 feet to the end and 

hook the stretcher bar there. Then put a temporary tension band where you can hook 

the come-along and hook the other end to the stretcher bar. Now that you have this set-up, 

slowly crank it tight, up to the point where there’s still enough tension that 

you can’t squeeze the fence with your fingers.

Step 15

Now that the fabric is tight, insert a tension bar in the fabric and the tension bands 

of the terminal post like what we did earlier in step 11. After tightening the bolt, y

ou can now remove the stretching contraption you made to tighten the fabric.

You’re now done with one side of the fence! Yay! Just repeat the process for 

the other sides to complete your DIY fence.

Step 16

Top hinge.

Bottom hinge.

Now that you’ve completed the fence, time to install the gate. Start with the post side of the hinges. Install the top and bottom hinges about

 8 inches from the top and bottom of your post.

REMEMBER: The top hinge pin faces downward and the bottom hinge pin faces upward. You do not want confusing these two.

Step 17

Attach the frame hinges loosely to the gate and set it about 2″ off the ground, 

use blocks if you have to. You can now adjust the bottom frame hinge to attach to the bottom 

post hinge and tighten the bolts. Repeat with the top hinges.

Step 18

Lastly attach the latch. Decide what height is comfortable and attach it with a bolt.

And that’s it. Just don’t forget to check if your gate swings freely. In case it doesn’t, 

don’t worry, all you have to do is adjust the hinges. To maintain your new chain link fence, 

just put oil on the hinges once a year and clean any dirt with a hose.

Note:This article is quoted from you feel that this article has violeted your copyrights in any way,please

contact us at,we will get it solved as soon as possible

Leave a Reply

Your email address will not be published. Required fields are marked *